PH 125 Midterm: ph125_f14_exam4_SOLN (1)

12 views5 pages

turquoisegnu128

31 Jan 2019

School

University of Alabama

Department

Course

PH 125

Professor

All

For unlimited access to Study Guides, a Grade+ subscription is required.

Document Summary

= 2t1 1. 4 s (1) (2: an aircraft door closes by pushing it inside the airplane rst. We will assume p = 0 outside the aircraft, and p = 0. 9 atm inside during ight. Solution: the force will be the surface area of the door exposed to the outside pressure times the pressure di erence. That means the area of the door minus the area of the seal. The force to overcome is due to the pressure di erence between inside and out, and that pressure di erence only exists over the part of the door that isn"t in contact with the seal. If you imagined the door as a rubber sheet, think about where it would bulge out - only where there isn"t a seal, because that"s the only place the door feels" the pressure di erence. The area of the door minus the sealing surface is 1. 9 by 0. 6 m, or a = 1. 14 m2.

Related Questions

which of the vectors below best represents the direction of the impulse vector j⃗ ?

To learn about the impulse-momentum theorem and its applications in some common cases.

Using the concept of momentum, Newton's second law can be rewritten as

?F? =dp? dt, (1)

where ?F? is the net force F? net acting on the object, and dp? dt is the rate at which the object's momentum is changing.

If the object is observed during an interval of time between times t1 and t2, then integration of both sides of equation (1) gives

?t2t1?F? dt=?t2t1dp? dtdt. (2)

The right side of equation (2) is simply the change in the object's momentum p2??p1?. The left side is called the impulse of the net force and is denoted by J? . Then equation (2) can be rewritten as

J? =p2??p1?.

This equation is known as the impulse-momentum theorem. It states that the change in an object's momentum is equal to the impulse of the net force acting on the object. In the case of a constant net force F? net acting along the direction of motion, the impulse-momentum theorem can be written as

F(t2?t1)=mv2?mv1. (3)

Here F, v1, and v2 are the components of the corresponding vector quantities along the chosen coordinate axis. If the motion in question is two-dimensional, it is often useful to apply equation (3) to the x and y components of motion separately.

( The following questions will help you learn to apply the impulse-momentum theorem to the cases of constant and varying force acting along the direction of motion. First, let us consider a particle of mass m moving along the x-axis. The net force F is acting on the particle along the x-axis. F is a constant force.)

A) The particle starts from rest at t=0. What is the magnitude p of the momentum of the particle at time t? Assume that t>0.

B) The particle starts from rest at t=0. What is the magnitude v of the velocity of the particle at time t? Assume that t>0.

C) The particle has the momentum of magnitude p1 at a certain instant. What is p2, the magnitude of its momentum ?t seconds later?

D) The particle has the momentum of magnitude p1 at a certain instant. What is v2, the magnitude of its velocity ?t seconds later?

E) Find the magnitude of the impulse J delivered to the particle.

F) Which of the vectors below best represents the direction of the impulse vector J??
(Figure 1)

1
2
3
4
5
6
7
8

puceworm982

Good Vibes: Introduction to Oscillations

The conditions that lead to simple harmonic motion are as follows:

There must be a position of stable equilibrium.

There must be a restoring force acting on the oscillating object. The direction of this force must always point toward the equilibrium, and its magnitude must be directly proportional to the magnitude of the object's displacement from its equilibrium position. Mathematically, the restoring force F⃗ is given by ⃗, where is the displacement from equilibrium and k is a constant that depends on the properties of the oscillating system.

The resistive forces in the system must be reasonably small.

Consider a block of mass m attached to a spring with force constant k, as shown in the figure(Figure 1) . The spring can be either stretched or compressed. The block slides on a frictionless horizontal surface, as shown. When the spring is relaxed, the block is located at x=0. If the block is pulled to the right a distance A and then released, A will be the amplitude of the resulting oscillations.

Assume that the mechanical energy of the block-spring system remains unchanged in the subsequent motion of the block.

Part A

After the block is released from x=A, it will

(a) remain at rest

(b) move to the left until it reaches equilibrium and stop there.

(d) move to the left until it reaches x=−A and then begin to move to the right.

The time it takes the block to complete one cycle is called the period. Usually, the period is denoted T and is measured in seconds.

The frequency, denoted f, is the number of cycles that are completed per unit of time: f=1/T. In SI units, f is measured in inverse seconds, or hertz (Hz).

Part B

If the period is doubled, the frequency is

(a) unchanged

(b) doubled

Part C

An oscillating object takes 0.10 s to complete one cycle; that is, its period is 0.10 s. What is its frequency f?

Express your answer in hertz.

Part D

If the frequency is 40 Hz, what is the period T?

Express your answer in seconds.

The following questions refer to the figure (Figure 2) that graphically depicts the oscillations of the block on the spring.

Note that the vertical axis represents the x-coordinate of the oscillating object, and the horizontal axis represents time.

Part E

Which points on the x-axis are located at a distance A from the equilibrium position?

(a) R only

(b) Q only

Part F

Suppose that the period is T. Which of the following points on the t-axis are separated by the time interval T?

(a) K and L

(b) K and M

(d) L and N

(e) M and P

Now assume for the remaining Parts G - J, that the x coordinate of point R is 0.12 m and the t coordinate of point K is 0.0050 s.

Part G

What is the period T?

Express your answer in seconds.

Part H

How much time t does the block take to travel from the point of maximum displacement to the opposite point of maximum displacement?

Express your answer in seconds.

Part I

What distance d does the object cover during one period of oscillation?

Express your answer in meters.

Part J

What distance d does the object cover between the moments labeled K and N on the graph?

Express your answer in meters.

emeraldyak680

PH 125 Midterm: ph125_f14_exam4_SOLN (1)

Document Summary

Get access

Related Documents

PH 125 Midterm: ph125_f14_exam4

PH 125 Midterm: ph125_s09_exam3 (1)

PH 125 Midterm: ph125_f17_exam1

Related Questions