CHEM 20 Study Guide - Midterm Guide: Sodium Hydroxide, Lithium Aluminium Hydride, Oxepin

29 views10 pages

turquoisegnu128

9 Jan 2019

School

Harvard University

Department

Chemistry and Chemical Biology

Course

CHEM 20

Professor

All

For unlimited access to Study Guides, a Grade+ subscription is required.

Document Summary

Rahul: this exam consists of 8 problems on 8 pages, plus this cover sheet, and one page for scratch work at the end of the exam, all answers must be written in the spaces provided. Answers written on the back of a page will not be graded. Anything written on the scratch page will not be graded: you are allowed to use a set of molecular models for this exam. ________________ / 100: each of the following transformations can be carried out in three or fewer steps. Fill in the reagents required for each step. If a step is not needed, please put an x through that step. _______ / 12: fill in each box with the single major organic product of the indicated transformation. Be sure to indicate the correct stereochemistry if it is relevant! Nh2: nano2 , hcl, cucn, lialh4, h+ workup. Nh2: br2 , naoh, nano2 , hcl, h3po2.

Related Questions

give chemical equations and synthesis reactions for the TiO2 solar cell

dye + light â dye*

dye* + TiO2 â e- (TiO2) + oxidized dye

oxidized dye + 3/2 I- â dye + Â½ I3 -

Â½ I3 - + e- (counter electrode) â 3/2 I

PROCEDURE

Preparation of TiO2 paste Grind about 0.5 gram of nanocrystalline titanium dioxide (TiO2) in a mortar and pestle with a few drops of very dilute acetic acid. Alternate grinding and addition of a few drops of very dilute acetic acid until you obtain a colloidal suspension with a smooth consistency, somewhat like latex paint. A toothpaste-like consistency is too thick. Also mix in a drop of clear dishwashing detergent as a surfactant. This quantity of TiO2 is enough for several solar cells. For easier distribution, transfer the TiO2 paste to a syringe. Wrap the end of the syringe with parafilm to keep the paste from drying out when not in use. (If the paste dries out, the titanium dioxide will need more water. See previous step.) Preparing the electrode 1. Preheat your hotplate. 2. Obtain two pieces of conducting glass (fluorine doped tin oxide). One will be your anode with the titanium dioxide film and dye, the other the cathode. 3. Identify the conducting side of a tin oxide-coated piece of glass by using a multimeter to measure resistance. The conducting side will have a resistance of 20-30 ohms. Switch the multimeter to the resistance setting (â¦) and test the piece of glass for conductivity. Only one side is conductive and this is the side you must use as a substrate for the titanium dioxide film and dye. 4. With the conducting side up, tape the glass on three sides to the center of a spill tray using one thickness of tape. Wipe off any fingerprints or oils using a tissue wet with ethanol. Opposite sides of tape will serve as a spacer (see below) so the tape should be flat and not wrinkled. The third side of tape gives an uncoated portion where an alligator clip will be connected. Applying the film 5. Add a small amount of titanium dioxide paste and quickly spread by pushing down and across with a microscope slide before the paste dries. The tape serves as a 40-50 micrometer spacer to control the thickness of the titanium dioxide layer if you push down. 6. Wait approximately two minutes for the film to dry. Carefully remove the Scotch tape border, paying attention to not splatter any of the wet paste or scratch the surface. 7. Carefully place the piece of glass on top of your preheated hotplate. Keep it there for 20 minutes. The surface turns brown as the organic solvent and surfactant dries and burns off to produce a white or green sintered titanium dioxide coating. (Note: this requires a plate that gets quite hot.) Allow the glass to slowly cool by turning off the hotplate. The sample will look quite similar before and after heating; you only know it is done if you have observed the darkening stage along the way. Preparing the dye 8. While the film is heating/cooling, begin to prepare the dye. Obtain one (1) raspberry or blackberry and crush it in a beaker. Add 3-4 drops of deionized water and continue to crush the berries, obtaining red juice.

9. Remove the cooled piece of glass (your anode) and place enough berry dye on the titanium dioxide film to completely cover it. Keep it there for 10 minutes. The white TiO2 will change color as the dye is absorbed and complexed to the Ti(IV). 10. Rinse gently with water to remove any berry solids and then with ethanol to remove water from the porous TiO2. The ethanol should have evaporated before the cell is assembled. Preparing the Counter electrode 11. Using a pencil, âcolor inâ the conductive side of the second piece of glass. It will take on a slight gray color. The graphite will function as a catalyst for the redox electrolyte. Make sure that this is done on the conductive side! Wipe off any carbon along the perimeter of three sides of the carbon-coated glass plate using a dry cotton swab. Assembling the cell 12. Place the titanium dioxide/dye electrode face up on the lab bench. Place the counter electrode on top of it, offsetting it so that the film is still covered by the counter electrode, but there is about â â of the glass exposed for connections on both electrodes. Do not rub or slide the plates.

13. Clamp the two electrodes together using two binder clips. They should be placed on the sides adjacent to the electrodes. 14. Add the redox electrolyte by placing 1 drop of a triiodide solution to opposite edges of the plate. Capillary action will cause the KI3 solution to travel between the two plates. (The KI3 electrolyte solution consists of 0.5 M KI and 0.05 M I2 in anhydrous ethylene glycol.) The solution can corrode the alligator clips in the next step so wipe off an excess. Properties of the cell Connect a multimeter using an alligator clip to each plate (the negative electrode is the TiO2 coated glass and the positive electrode is the carbon coated glass). â¢ Test the current and voltage produced by solar illumination, or... â¢ Test the current and voltage produced by illumination from an overhead projector..

CHEM 20 Study Guide - Midterm Guide: Sodium Hydroxide, Lithium Aluminium Hydride, Oxepin

Document Summary

Get access

Related textbook solutions

Chemistry: Structure and Properties

Physics: Principles with Applications

Basic Chemistry

Principles of Chemistry Molecular Approach

Chemistry: Structure and Properties

Principles of Chemistry Molecular Approach

Chemistry: A Molecular Approach

Chemistry: A Molecular Approach

Principles of Chemistry: A Molecular Approach

Chemistry: The Central Science

Related Documents

CHEM 20 Midterm: Exam 4 S20 2014

CHEM 20 Study Guide - Midterm Guide: Phenyl Group, Methyl Iodide, Diastereomer

CHEM 20 Study Guide - Midterm Guide: Alkyne, Meta-Chloroperoxybenzoic Acid, Proton Nuclear Magnetic Resonance

Related Questions