Log in
Physics
1
answer
0
watching
220
views

In mechanics, an object whose position relative to a rest position is given by a generalized cosine (or sine) function.

Is called a simple harmonic oscillator is a mass suspended from a spring and a pendulum swinging through a small angle, in the absence of frictional damping forces. When we take damping force into account, we obtain a damped harmonic oscillator:

 

A mass on a spring is undergoing simple harmonic motion so that it's vertical position at time t seconds is given by 

 Centimetres below the rest position.

What is its vertical position at time t=0 sec?

 

Watch
1
answer
0
watching
220
views

For unlimited access to Homework Help, a Homework+ subscription is required.

Sagar Yadav
Sagar YadavLv10
15 Dec 2020

Unlock all answers

Get 1 free homework help answer.
Already have an account? Log in
Share

Related textbook solutions

Physics: Principles with Applications
7th Edition, 2013
Giancoli
ISBN: 9780321625922

Related questions

In mechanics, an object whose position relative to a rest position is given by a generalized cosine or sine function.

Is called a simple harmonic oscillator. Examples of the simple harmonic oscillator are a mass suspended from a spring and a pendulum swinging through a small angle, in the absence of frictional damping forces. When we take damping forces into account, we obtain a damped harmonic oscillator:

 

A mass on a spring is undergoing simple harmonic motion so that its vertical position at time t seconds is given by 

Cm below the rest position.

The frequency of oscillation is defined as the reciprocal of the period. What is the frequency of the oscillation of spring?

 

 

Good Vibes: Introduction to Oscillations

 

The conditions that lead to simple harmonic motion are as follows:

There must be a position of stable equilibrium.

There must be a restoring force acting on the oscillating object. The direction of this force must always point toward the equilibrium, and its magnitude must be directly proportional to the magnitude of the object's displacement from its equilibrium position. Mathematically, the restoring force F⃗  is given by ⃗, where is the displacement from equilibrium and k is a constant that depends on the properties of the oscillating system.

The resistive forces in the system must be reasonably small.

Consider a block of mass m attached to a spring with force constant k, as shown in the figure(Figure 1) . The spring can be either stretched or compressed. The block slides on a frictionless horizontal surface, as shown. When the spring is relaxed, the block is located at x=0. If the block is pulled to the right a distance A and then released, A will be the amplitude of the resulting oscillations.

Assume that the mechanical energy of the block-spring system remains unchanged in the subsequent motion of the block.

Part A

After the block is released from x=A, it will

(a) remain at rest

(b) move to the left until it reaches equilibrium and stop there. 

(c) move to the left until it reaches x= –A and stop there. 

(d) move to the left until it reaches x=−A and then begin to move to the right.

 

 

 

The time it takes the block to complete one cycle is called the period. Usually, the period is denoted T and is measured in seconds.

The frequency, denoted f, is the number of cycles that are completed per unit of time: f=1/T. In SI units, f is measured in inverse seconds, or hertz (Hz).

Part B

If the period is doubled, the frequency is

(a) unchanged 

(b) doubled 

(c) halved

 

Part C

An oscillating object takes 0.10 s to complete one cycle; that is, its period is 0.10 s. What is its frequency f?

Express your answer in hertz.

 

Part D

If the frequency is 40 Hz, what is the period T?

Express your answer in seconds.

 


The following questions refer to the figure (Figure 2) that graphically depicts the oscillations of the block on the spring.

Note that the vertical axis represents the x-coordinate of the oscillating object, and the horizontal axis represents time.

 

Part E

Which points on the x-axis are located at a distance A from the equilibrium position?

(a) R only

(b) Q only

(c) both R and Q

 

Part F

Suppose that the period is T. Which of the following points on the t-axis are separated by the time interval T?

(a) K and L

(b) K and M 

(c) K and P

(d) L and N 

(e) M and P 

 

 

Now assume for the remaining Parts G - J, that the x coordinate of point R is 0.12 m and the t coordinate of point K is 0.0050 s.

Part G

What is the period T?

Express your answer in seconds.

 

Part H

How much time t does the block take to travel from the point of maximum displacement to the opposite point of maximum displacement?

Express your answer in seconds.

 

Part I

What distance d does the object cover during one period of oscillation?

Express your answer in meters.

 

Part J

What distance d does the object cover between the moments labeled K and N on the graph?

Express your answer in meters.

Weekly leaderboard

Home
Homework Help 3,900,000
Physics 110,000
Start filling in the gaps now
Log in