Log in
Physics
2
answers
1
watching
391
views
28 Aug 2018

14.74 ... An object with mass 0.200 kg is acted on by an elas- tic restoring force with force constant 10.0 N/m. (a) Graph elastic potential energy U as a function of displacement x over a range of x from -0.300 m to +0.300 m. On your graph, let 1 cm = 0.05 J vertically and 1 cm = 0.05 m horizontally. The object is set into oscillation with an initial potential energy of 0.140 J and an initial kinetic energy of 0.060 J. Answer the following questions by refer- ring to the graph. (b) What is the amplitude of oscillation? (c) What is the potential energy when the displacement is one-half the amplitude? (d) At what displacement are the kinetic and potential energies equal? (e) What is the value of the phase angle • if the initial velocity is positive and the initial displacement is negative?

word_media_image1.png
Watch
2
answers
1
watching
391
views

For unlimited access to Homework Help, a Homework+ subscription is required.

Avatar image
Liked by astrait and 2 others

Unlock all answers

Get 1 free homework help answer.
Already have an account? Log in
Share
Lelia Lubowitz
Lelia LubowitzLv2
29 Aug 2018
Already have an account? Log in
Share

Related textbook solutions

Physics: Principles with Applications
7th Edition, 2013
Giancoli
ISBN: 9780321625922

Related questions

A horizontal spring with a spring constant of 20.0 N/m is attached to a 0.750 kg mass on a horizontal, frictionless table. The mass is pulled until the spring is stretched to 10.0 cm, then released at time t = 0 s.

a. What is the angular frequency, frequency, and period of the oscillation?

b. What is the amplitude of the motion?

c. At what time will the mass first pass the equilibrium position?

d. At what position is the block after 1.00 seconds?

e. How fast is it going when it passes the equilibrium position?

f. How fast is it going at 2.00 seconds?

g. How fast is it going when it is at the halfway point to the equilibrium position?

h. At what position is it going 0.250 m/s?

i. What is the total mechanical energy of the block?

j. At what position is the energy evenly split between kinetic and spring potential energy?

Good Vibes: Introduction to Oscillations

 

The conditions that lead to simple harmonic motion are as follows:

There must be a position of stable equilibrium.

There must be a restoring force acting on the oscillating object. The direction of this force must always point toward the equilibrium, and its magnitude must be directly proportional to the magnitude of the object's displacement from its equilibrium position. Mathematically, the restoring force F⃗  is given by ⃗, where is the displacement from equilibrium and k is a constant that depends on the properties of the oscillating system.

The resistive forces in the system must be reasonably small.

Consider a block of mass m attached to a spring with force constant k, as shown in the figure(Figure 1) . The spring can be either stretched or compressed. The block slides on a frictionless horizontal surface, as shown. When the spring is relaxed, the block is located at x=0. If the block is pulled to the right a distance A and then released, A will be the amplitude of the resulting oscillations.

Assume that the mechanical energy of the block-spring system remains unchanged in the subsequent motion of the block.

Part A

After the block is released from x=A, it will

(a) remain at rest

(b) move to the left until it reaches equilibrium and stop there. 

(c) move to the left until it reaches x= –A and stop there. 

(d) move to the left until it reaches x=−A and then begin to move to the right.

 

 

 

The time it takes the block to complete one cycle is called the period. Usually, the period is denoted T and is measured in seconds.

The frequency, denoted f, is the number of cycles that are completed per unit of time: f=1/T. In SI units, f is measured in inverse seconds, or hertz (Hz).

Part B

If the period is doubled, the frequency is

(a) unchanged 

(b) doubled 

(c) halved

 

Part C

An oscillating object takes 0.10 s to complete one cycle; that is, its period is 0.10 s. What is its frequency f?

Express your answer in hertz.

 

Part D

If the frequency is 40 Hz, what is the period T?

Express your answer in seconds.

 


The following questions refer to the figure (Figure 2) that graphically depicts the oscillations of the block on the spring.

Note that the vertical axis represents the x-coordinate of the oscillating object, and the horizontal axis represents time.

 

Part E

Which points on the x-axis are located at a distance A from the equilibrium position?

(a) R only

(b) Q only

(c) both R and Q

 

Part F

Suppose that the period is T. Which of the following points on the t-axis are separated by the time interval T?

(a) K and L

(b) K and M 

(c) K and P

(d) L and N 

(e) M and P 

 

 

Now assume for the remaining Parts G - J, that the x coordinate of point R is 0.12 m and the t coordinate of point K is 0.0050 s.

Part G

What is the period T?

Express your answer in seconds.

 

Part H

How much time t does the block take to travel from the point of maximum displacement to the opposite point of maximum displacement?

Express your answer in seconds.

 

Part I

What distance d does the object cover during one period of oscillation?

Express your answer in meters.

 

Part J

What distance d does the object cover between the moments labeled K and N on the graph?

Express your answer in meters.

Related Documents

PHYS 1003 Lecture Notes - Lecture 17: Simple Harmonic Motion, Restoring Force, Equilibrium Point
scarletmouse10
PHYS 1003 Lecture Notes - Lecture 17: Torsion Spring, Simple Harmonic Motion, Angular Frequency
lemonwasp446
PHYS 6B Chapter Notes - Chapter 12: Simple Harmonic Motion, Circular Motion, Angular Acceleration

Weekly leaderboard

Home
Homework Help 3,900,000
Physics 110,000
Start filling in the gaps now
Log in