PHYS 1003 Lecture Notes - Lecture 7: Friction, Net Force, Gravitational Constant

23 views4 pages

lemonwasp446

17 Oct 2016

School

Department

Course

Professor

For unlimited access to Class Notes, a Class+ subscription is required.

Document Summary

If the applied force attempting to move the object is less than the maximum possible. F s,max = s f|| n|| u static friction force , then the object will not move. Raise on end of the surface until the object starts to slide (be precise, try to tilt slow) The angle of the tilt can be used to determine the static friction coefficent. Kinetic friction applies to objects which are already in motion. ** usually, f k is about 10% less than f s. In other words, it"s easier to keep something in motion than it is to get an object to start moving. ** an object moving on an inclined plane has three forces acting on it. Objects moving through a fluid ( liquid or gas ) experience a type of friction force called the drag force which acts to oppose motion. Depends on surface area that faces the flow.

Related Questions

1. A block is placed on a plane whose angle of inclination is 30˚. The coefficients of static and kinetic friction for the block on the inclined plane are both 0.2. The block
(A) remains stationary on the inclined plane.
(B) accelerates down the inclined plane.
(C) travels down the inclined plane at a constant velocity.
(D) travels up the inclined plane at a constant velocity.
(E) accelerates up the inclined plane.

2. An object with a mass of 5.5 kg is allowed to slide from rest down an inclined plane. The plane makes an angle of 30˚ with the horizontal and is 72 m long. The coefficient of friction between the plane and the object is 0.35. The speed of the object at the bottom of the plane is?

3. A 5-kg object slides down a frictionless surface inclined at an angle of 30˚ from the horizontal. The total distance moved by the object along the plane is 10 meters. The work done on the object by the normal force of the surface is?

4. A mass m = 2.5 kg is sliding along a frictionless table with initial speed v as shown in the figure. It strikes a coiled spring that has a force constant k = 500 N/m and
compresses it a distance x=5.0 cm. The initial speed v of the block was..?

5. The graph shows how the position of a particle depends on time. Which choice is closest to the instantaneous speed of the particle at t = 3s?
(A) 0.40 m/s
(B) 0.67 m/s
(C) 0.75 m/s
(D) 1.50 m/s
(E) 2.22 m/s

6. Calculate the work done by a force, F = 2x i, along the
path (0, 0) -> P₁(2, 0) -> P2(2, 2).

turquoisearmadillo973

I am so lost onwere to even begin. I just need help trying to find the Ñ² (angle)for part part 1 of the experiment if anyone can just explain how todo that and maybe give me a step-by-step example so I can finishthe rest. Thank you! Experiment 6 ~ Friction

Purpose:

In this lab, you will make some basic measurements of friction.You will measure the coefficients of staticfriction between several combinations of surfaces using aninclined plane, and you will measure the coefficient ofkinetic friction between two of the combinationsof surfaces you used in the static friction part of thisexperiment.

Part 1: StaticFriction

Theory:

The coefficient of static frictionm_s can be measured experimentally foran object placed on an inclined plane (a.k.a. ramp, a.k.a. hill).The coefficient of static friction is related to the criticalangle q_c for the ramp, at whichthe object just begins to slide. Using what we havecovered in class, you can derive this relationshipyourself! At this critical angle, static friction preventing theobject from sliding down the hill is just exactly equal to thecomponent of the objectâs weight along the hill. If the componentof the weight along the hill were just a little greater, it wouldovercome friction, and the object would start to slide down. Thefree body diagram for this situation will look like the figuresketched below. Use this diagram to find an equation that relatesm_s toq_c.

F_N = NormalForce = mg cos(Î¸)

F_F =Î¼_s x F_N = Î¼_s mg cos(Î¸)

Î£F_x = mA_x = F_Gx - F_F = ?

F_Gx = mgsin(Î¸)

Hint #1: the angle q of the incline is the same as theangle between the normal force N and the weightmg. Why?

Hint #2: The weight mg can be broken into twocomponents. One component is along the incline(W_H). The other component is âpressinginto the hillâ, and is equal in magnitude to the normal forceN. (This is an example of a situation where the normalforce is not equal to the weight!) Remember that you need to usethe normal force to calculate friction, sincef=mN. Now calculate what the angle ofthe incline should be, so that the component of the weight down thehill is just exactly balanced by friction.

Equipment:

For this lab you will need to share the following ramps andblocks with other lab groups:

Ramps Blocks

Aluminum Aluminum

ParticleBoard Brass

StainlessSteel Plexiglass

Plastic Copper

Rubber

Steel

Wood

Experiment:

Test at least 5 different combinations of materials. Record thematerial of the block and the ramp for each combination.

1. Measure and record the length of theinclined plane you will be using. (This is thehypotenuse of the right triangle!)

2. Place the block on the plane and begin tiltingthe plane just until the point when the block begins to slide.

3. Measure the height of the raisedend of the inclined plane at this point. (This is theopposite side of the right triangle!) You cancalculate the angle from the measurements of the two sides.

4. Repeat the height measurement at least 3 timesfor each combination of materials. Record all the measurements inthe table below. Then,

(a) calculate the angle from the measurements of the hypotenuseand opposite side you just obtained

(b) use the equation you derived above in order to calculate thecoefficient of kinetic friction from the angle.

Block: woodenblock Block: cooper

Ramp:particleboard Ramp: particle board

Length of ramp:0.61(m) Length of ramp: 0.61(m)

Height(m)	Ñ²	Ms	Height(m)	Ñ²	Ms
0.24			0.26
0.25			0.31
0.245			0.345

avg m_s: ______ s : _______ avg m_s: ______ s : _______

Block:aluminum Block:particle board block

Ramp: solidewood Ramp: solide wood

Length of ramp:0.605(m) Length of ramp: 0.605(m)

Height(m)	Ñ²	s	Height(m)	Ñ²	s
0.15			0.23
0.16			0.165
0.16			0.195

avg m_s: ______ s : _______ avg m_s: ______ s : _______

5. Remember that in class we said that friction does not dependon surface area. You can easily test whether or not this iscorrect. Choose a block/ramp combination not already tested, andmake sure the block is not a cube or cylinder. Place the block sothat the side with the larger surface area is in contact with theboard. Now measure the angle at which the block just begins toslide (by measuring the hypotenuse and opposite sides of thecorresponding right triangle). As before, calculate the coefficientof friction from the angle you measured, using your equation.Repeat this process with the side of the block with the smallersurface area in contact with the board. Enter this data in thesmall tables below.

Block (larger end) :_________ Block (smaller end):__________

Ramp:_______________ Ramp: ________________

Length of ramp:______(m) Length of ramp: ______(m)

Height(m)	s	Height(m)	s

avg m_s: ______ s : _______ avg m_s: ______ s : _______

Part 2: KineticFriction

Theory:

You can calculate the coefficient of kinetic friction,m_k, using a variation of the methodyou used for the coefficient of static friction. For thecoefficient of kinetic friction, you can use the same free bodydiagram as the one drawn on the first page. But now, thecombination of W_H and the force offriction will need to add up such that the block will slide at aconstant speed. Think of Newtonâs first and second laws when youset up this equation. Derive a relationship between the criticalangle and the coefficient of kinetic friction.

Experiment:

You can measure m_k using aprocedure similar to the one you used to measurem_s. This time, just pick twocombinations of materials. The combinations you pick for this partof the experiment have to be combinations you alreadyused for the static friction part of the experiment, because thepoint is to compare m_sandm_k!

1. Measure and record the length ofthe inclined plane you will be using.

2. Raise the plane high enough for the blockto begin moving. Begin lowering the plane just until the pointwhen the block begins to slow down. (Alternatively, raise theboard while tapping the block until block moves at a constantrate.)

3. Measure the height of the raisedend of the inclined plane at this point.

4. Repeat the height measurement at least 3times for each combination of materials. Record all themeasurements in the table below. Then,

(a) calculate the angle from the measurements of the hypotenuseand opposite side you just obtained

(b) use the equation you derived above in order to calculate thecoefficient of kinetic friction from the angle.

Block (from part 1) :_________ Block (from part 1):__________

Ramp:_______________ Ramp: ________________

Length of ramp:______(m) Length of ramp: ______(m)

Height(m)	k	Height(m)	k

avg m_k: ______ s : _______ avg m_k: ______ s : _______

Analysis:

Calculate the mean value and standard deviation of thecoefficient of static friction that you measured, for each set ofmaterials.

ramp/board pair		Standard deviation




(larger end)
(smaller end)

Calculate the mean value and standard deviation of thecoefficient of kinetic friction that you measured, for each set ofmaterials.

ramp/board

pair

Standard

deviation

Questions:

1. How do the values of m_s compareto the values of m_k? (Of course, youcan only compare them for the same pairs of materials.)

2. Is the relationship betweenm_sand m_kwhat you expected?

3. Of the two parts of the experiment, measurement ofm_sand measurement ofm_k, which had more sources of error?What were some of the sources of error?

4. Could m_k orm_s ever be greater than 1? Explain whyor why not.

5. Is the coefficient of friction the same as when the block wasstanding on its larger (or smaller) end?

6. Think about your results. Do they make sense when youconsider your everyday experiences?

1) An object is moving with constant velocity. Which of thefollowing statements is true?
a) A constant force is being applied in the direction ofmotion.
b) A constant force is being applied in the direction opposite ofmotion.
c) There are no forces acting on the object.
d) The net force on the object is zero.
e) There is no frictional force acting on the object.

2) You apply the same force to two objects. Object 1 has mass M andobject 2 has mass 5M.
a) ten times that of object 1 b) five times that of object 1
c) the same as that of object 1 d) 1/5 as that of object 1

3) An object of weight W is in free-fall close to the surface ofEarth. What is the force that the object exerts on Earth?
a) a force greater than W b) a force less than W
c) a force equal to W d) no force at all

4) A parking crate slides down an inclined ramp at constantvelocity. Thus we can deduce that _
a) a frictional force is acting on it
b) a net downward force is acting on it
c) a net upward force is acting on it
d) it is not acted on by appreciable normal force
e) it is not acted on by appreciable gravitational force

5) A person applies a constant force of 20N to a rock of mass1000kg for a total of 20 seconds. What is the work done by thisperson if the person does not move at all by this appliedforce?
a) 1000J b) 2000J c) 20,000J d) 0J e) 400J

6) If the net work done on an object is positive, then theobject's kinetic energy.
a) decreases b) remains the same c) increases d) is zero

7) You throw a ball straight up. Compare the sign of the workdone by gravity while the ball goes up with the sign of the workdone by gravity while it goes down.
a) Work is + on the way up and + on the way down
b) Work is + on the way up and - on the way down
c) Work is - on the way up and + on the way down
d) Work is - on the way up and - on the way down

PHYS 1003 Lecture Notes - Lecture 7: Friction, Net Force, Gravitational Constant

Document Summary

Get access

Related textbook solutions

Physics: Principles with Applications

Related Documents

PHYS 1003 Lecture 4: 4. Newton’s Laws of Motion

PHYS 1003 Study Guide - Quiz Guide: Free Body Diagram, Friction, Speed

PHYS 1003 Lecture Notes - Lecture 8: Energy, Glossary Of Riemannian And Metric Geometry

Related Questions